1： When operating the automatic feeding mixer, keep the heel close to the floor of the cab, keep the pedal parallel to the accelerator pedal, and press the accelerator pedal slowly.

2：自动进纸混合器运行时，节气门应始终保持稳定。在正常工况下，节气门开度约为70％。

2: The throttle should always be stable when the automatic feeder mixer is running. Under normal operating conditions, the throttle opening is about 70%.

3：操作自动上料混凝土搅拌车时，脚踏板应与制动踏板分开，并平放在驾驶室地板上。自动装载搅拌机通常在不平坦的建筑工地上工作。如果您的脚一直踩在制动踏板上，您的身体会上下移动，驾驶员会无意间踩到制动踏板。通常情况下，有必要通过控制节气门的减速度来控制发动机和变速齿轮的状态。这不仅避免了频繁的制动和制动系统的过热，而且还提高了自动供料搅拌机的便利性。

3: When operating the automatic charging mixer, the pedal should be separated from the brake pedal and placed flat on the cab floor. Automatic loading mixer usually works on uneven construction site. If you step on the brake pedal all the time, your body will move up and down, and the driver will step on the brake pedal unintentionally. Usually, it is necessary to control the state of the engine and gear by controlling the deceleration of the throttle valve. This not only avoids frequent braking and overheating of the braking system, but also improves the convenience of the automatic feeding mixer.

4：在操作自动供料搅拌机时，尤其是在操作铲斗时，必须在节流阀稳定的同时定期向上提起提升杆和铲斗操作杆，以向铲斗中填充物料。

4: When operating the automatic feeding mixer, especially when operating the bucket, the lifting rod and bucket operating lever must be lifted up regularly to fill the bucket while the throttle valve is stable.

5：禁止轮胎侧滑。当混凝土自动上料混凝土搅拌车运行时，遇到阻力时，加速器突然踩踏，轮胎经常打滑。此现象通常是由不当的驾驶员操作引起的。

5: Do not allow tire sideslip. When the concrete automatic loading mixer runs, when encountering resistance, the accelerator suddenly steps on, and the tire often slips. This phenomenon is usually caused by improper driver operation.

这将增加油耗并损坏轮胎。第二是防止后轮倾斜。由于自动上料混凝土搅拌车的钻孔能力强，驾驶员通常会铲掉坚硬的原土和落基山脉。如果操作不正确，则将两个后轮简单地抬离地面。提升操作的地面惯性导致铲斗叶片破裂和变形。如果后轮高，钢板以及前框架和后框架等焊接部件都会断裂。第三是禁止上山。剃刮普通物料时，自动饲料搅拌机以2档运行，并且禁止惯性冲击2档以上的齿轮组。

This will increase fuel consumption and damage the tires. The second is to prevent the rear wheels from tilting. Due to the strong drilling capacity of the automatic charging mixer, the driver usually shovel away the hard original soil and Rockies. If the operation is not correct, simply lift both rear wheels off the ground. The ground inertia of the lifting operation causes the bucket blades to crack and deform. If the rear wheel is high, the steel plate and welded parts such as the front and rear frames will break. Third, it is forbidden to go up the mountain. When the mixer is above 2 gears, it is forbidden to impact the normal gear when shaving the feed automatically.