搅拌车减震器的保养应该注意什么?

 来源:http://www.jufengjiaobanji.com 日期:2020-09-21 发布人:admin
如果搅拌车的减震器失效或者出现问题,应首先查看减震器是否有漏油现象,用力按下保险杠,然后松开,假如搅拌车有两到三次的腾跃,就说明减震器是好的。搅拌车在缓慢行驶中紧急制动,此时如果车辆的振动比较厉害,就说明减震器有问题,需要拆下减震器将其直立,并把下端衔接环夹在台钳上,用力拉压减震杆数次,此时应有稳定的阻力,往上拉的阻力应大于向下的阻力,如果阻力不稳定或无阻力,可能是减震器内部缺油或阀门零件损坏,应终止修复或更换零件,并应立即送去维修。
If the shock absorber of the mixer fails or has problems, you should first check whether the shock absorber has oil leakage, press the bumper firmly, and then release it. If the mixer has two or three jumps, it shows that the shock absorber is good. When the mixer truck is running slowly, emergency braking is required. If the vibration of the vehicle is severe, it indicates that there is something wrong with the shock absorber. It is necessary to remove the shock absorber and put it upright. Clamp the lower end connecting ring on the bench vice, and pull and press the shock absorber rod several times. At this time, there should be stable resistance. The resistance upward should be greater than the downward resistance. If the resistance is unstable or there is no resistance, it may be the shock absorber In case of internal oil shortage or valve parts damage, repair or replacement parts shall be terminated and sent to repair immediately.
搅拌车减震器漏油一般是以下几个原因:
The oil leakage of the shock absorber of mixer truck is generally caused by the following reasons:
1. 减震器内部的清洁度不够好,有焊渣、铁屑等杂物导致油封磨损。
1. The internal cleanliness of the shock absorber is not good enough, and there are welding slag, iron chips and other debris causing oil seal wear.
2. 减震器的工作条件比较恶劣,外部的泥沙等杂物进入油封,导致其磨损漏油。
2. The working conditions of the shock absorber are relatively bad, and the external sand and other debris enter the oil seal, causing its wear and oil leakage.
全自动自上料搅拌车
3. 减震器油封的唇口老化,失去了密封的功能。
3. The lip of shock absorber oil seal is aged and lost its sealing function.
4. 可能是在喷底盘装甲的时候,减震器没有遮挡好,装甲附在减震器活塞杆上导致油封磨损而漏油。
4. It may be that when spraying the chassis armor, the shock absorber is not well covered, and the armor is attached to the shock absorber piston rod, resulting in oil seal wear and oil leakage.
5. 控制活塞运动的支杆需要在金属管的一端延长出来,所以这个部位必须得密封严密,一般的漏油都和密封不严有直接关系的。
5. The supporting rod controlling the piston movement needs to be extended at one end of the metal pipe, so this part must be sealed tightly. The general oil leakage is directly related to the loose sealing.
6. 一般搅拌车的液压的减震器漏油就说明它的使用年限已到。
6. Oil leakage of hydraulic shock absorber of general mixer truck indicates that its service life is up.
感谢您的阅读,此文的文章来源:全自动自上料搅拌车更多的内容和问题请点击:http://www.jufengjiaobanji.com我们会继续努力的为您提供服务,感谢您的支持!
Thank you for your reading. This article is from Zhongke. For more information and questions, please click: http://www.jufengjiaobanji.com We will continue to work hard to provide services for you, thank you for your support!