1. Universal turning parts are fault parts. Grease should be replenished in time, wear should be checked frequently, and repaired and replaced in time. The fleet should have a spare cardan shaft assembly to ensure recovery in a few minutes in the event of a failure.

2.确保液压油清洁。自上料微型搅拌车的工作环境不好，必须防止脏的水泥砂进入液压系统。应按手册要求定期更换液压油。一旦检查发现水或沙子混入了液压油中，则必须立即停止液压系统并更换液压油。

2. Make sure the hydraulic oil is clean. The working environment of self feeding Mini mixer is not good, so it is necessary to prevent the dirty cement sand from entering the hydraulic system. The hydraulic oil should be changed regularly according to the manual. Once water or sand is found mixed in the hydraulic oil, the hydraulic system must be stopped immediately and the hydraulic oil must be replaced.

3.确保液压油冷却装置有效。定期清洁液压油散热器，以防止散热器被水泥堵塞，检查散热器风扇是否正常运行，并防止液压油温度超过标准。只要液压元件确保液压油清洁，通常几乎不会发生故障，但是制造商的使用寿命不同。

3. Ensure that the hydraulic oil cooling device is effective. Regularly clean the hydraulic oil radiator to prevent the radiator from being blocked by cement, check the radiator fan for normal operation, and prevent the hydraulic oil temperature from exceeding the standard. As long as the hydraulic components ensure that the hydraulic oil is clean, there is usually almost no failure, but the service life of manufacturers is different.

通常，如果驱动器由于故障而停止工作，则混凝土罐将无法正常旋转，这将导致车辆中的混凝土报废，甚至整个罐中的混凝土也会在罐中凝结，从而导致全自动自上料搅拌车报废。因此，驱动装置是否可靠是使用中必须高度重视的问题。

Usually, if the driver stops working due to failure, the concrete tank will not rotate normally, which will lead to the scrapping of concrete in the vehicle, and even the concrete in the whole tank will coagulate in the tank, resulting in the scrapping of the concrete mixer. Therefore, whether the driving device is reliable or not is a problem that must be attached great importance in use.

自上料微型搅拌车堵塞处理步骤

Processing steps for blockage of self loading Mini mixer

设备本身的特性，自上料微型搅拌车广泛用于各种建筑物。长时间使用设备时，设备不可避免会出现不同的故障问题。其中，阻塞很常见，因此，当设备出现此类问题时，我们应如何合理处理？

Due to the characteristics of the equipment itself, self loading Mini mixer is widely used in various buildings. When the equipment is used for a long time, the equipment will inevitably have different fault problems. Among them, blocking is very common, so when the equipment has such problems, how should we deal with them reasonably?

1.每次充电前，请用水冲洗进水口，以在进水期间保持进水口湿润。

1. Before charging each time, please flush the water inlet with water to keep the water inlet moist during the water inlet period.

2.装载时，将装在车辆上的清洗水箱注满水。

2. When loading, fill the washing water tank on the vehicle with water.

3.充电后，冲洗进料口并清洁进料口附近的混凝土。

3. After charging, flush the inlet and clean the concrete near the inlet.

4.在施工现场卸货后，冲洗卸料斜槽，然后向混凝土储罐中添加30-40L的洗涤水；在车辆返回过程中，保持混凝土储罐缓慢旋转。

4. After unloading at the construction site, flush the discharge chute, and then add 30-40l washing water to the concrete storage tank; during the return of vehicles, keep the concrete storage tank rotating slowly.

5.请记住在下一次装载之前将混凝土储罐中的污水排干。

5. Please remember to drain the sewage from the concrete storage tank before the next loading.

6.每天彻底清洁混凝土储罐以及机器周围的入口和出口。自上料微型搅拌车的清洁点可确保没有水泥和混凝土结块。

6. Thoroughly clean the concrete storage tank and the entrance and exit around the machine every day. The cleaning point of the self loading Mini mixer ensures that there is no cement and concrete caking.