一、整车的外廓尺寸应符国家标准的规定。并按批准的产品图样及技术文件制造。

1、 The overall dimensions of the whole vehicle shall comply with the provisions of national standards. And according to the approved product drawings and technical documents.

二、外购件、外协件均应有制造厂的产品合格证，并符合相关标准的要求，经搅拌车生产厂检验合格后方可装配。

2、 The purchased parts and outsourcing parts shall have the product certificate of the manufacturer and meet the requirements of relevant standards. They can be assembled only after passing the inspection of the mixer manufacturer.

三、搅拌车的厂定大总质量不得超过底盘的大许用值，转向轴(轮)载质量和侧倾稳定角应符合GB7258的规定。

3、 The total mass of the mixer determined by the factory shall not exceed the maximum allowable value of the chassis, and the steering shaft (wheel) load mass and roll stability angle shall comply with the provisions of GB7258.

四、焊缝应均匀、平直。无漏焊、裂纹、央渣、表面应无毛边，包砂等现象。

4、 The weld should be even and straight. There shall be no weld leakage, crack, slag, burr and sand coating on the surface.

五、所有外露黑色金属表面均应作防锈处理。外表装饰漆应美观大方，符合GB7258的规定。

5、 All exposed ferrous metal surfaces shall be treated with anti rust treatment. The exterior decorative paint shall be beautiful and elegant, and comply with the provisions of GB7258.

六、从进料到输送卸料完毕，允许的长时间为90mh，且搅拌筒按规定连续运输不大于300转。搅拌车行驶时，高车速不得超过如50km/h

6、 The allowable time from feeding to discharging is 90mh, and the continuous transportation of mixing drum is not more than 300 revolutions. When the mixer is running, the high speed shall not exceed 50km / h

七、装入预拌混凝土在规定的搅动转速和输送时间运送到交贷地点后，泥凝土质量应符国标要求。

7、 After the ready mixed concrete is loaded and transported to the delivery place at the specified stirring speed and delivery time, the quality of the concrete should meet the requirements of the national standard.

八、进料斗出口尺寸不小于历650mm，距地面高度应不大于3.8m。

8、 The size of the feed hopper outlet shall not be less than 650mm, and the height from the ground shall not be more than 3.8m.

九、水泥搅拌车的出料速度不小于0.65m3/min，出料残余率小于2-5%。搅拌车的进料速度不小于2.7m3/min

9、 The discharging speed of cement mixer is not less than 0.65m3/min, and the discharging residual rate is less than 2-5%. The feeding speed of the mixer shall not be less than 2.7m3/min

十、输送应安装牢固。各连接部分部件不应有损坏、变形等现象，不应有上车与底盘偏离原先的固定装置的情况。

10、 The conveyor should be installed firmly. The connecting parts shall not be damaged or deformed, and the upper part and chassis shall not deviate from the original fixing device.

十一、车在大总质量状态下，以20km/h的速度府能通过14%的坡道外溢。

11、 Under the condition of large total mass, the vehicle can overflow through 14% of the ramp at the speed of 20km / h.

十二、制动性能府符合国标规定。行驶车外噪声应符国标要求。

12、 The braking performance meets the national standard. The noise outside the driving vehicle shall meet the requirements of the national standard.

十三、整车的各项密封性能良好，各密封面、管接头及所有连接部位均不得有渗油漏气的现象。

13、 The sealing performance of the whole vehicle is good, and all sealing surfaces, pipe joints and all connecting parts shall be free of oil and gas leakage.

莱州聚峰机械专注行业经营多年，专注于全自动自上料搅拌车的生产及研究，欢迎大家点击我们的网站http://www.jufengjiaobanji.com进行咨询及了解，欢迎大家访问.

Laizhou Jufeng machinery has been focusing on the industry for many years, focusing on the production and research of automatic self loading mixer. Welcome to our website http://www.jufengjiaobanji.com For consultation and understanding, welcome to visit