自动上料混凝土搅拌车该机器设备有时需求润滑以在长期运用期间坚持杰出的功用。那么在为设备添加润滑剂时需求留心什么？

Automatic loading concrete mixer this machine and equipment sometimes need lubrication to maintain outstanding function during long-term operation. So what should we pay attention to when adding lubricant to the equipment?

1.操作期间，请勿修理或润滑自动上料混凝土搅拌车。

1. During operation, do not repair or lubricate the automatic feeding concrete mixer.

2.守时在每个润滑脂嘴上参加黄油，每4小时用一个轴端密封润滑油，每周排水一次。

2. Be punctual, add grease on each grease fitting, seal the lubricating oil with a shaft end every 4 hours, and drain water once a week.

3.运用自动上料混凝土搅拌车后，依据需求在每个润滑点添加必要的润滑剂（滚筒轴，滚筒，钢丝绳，其他有用部件）。

3. After using the automatic feeding concrete mixer, add the necessary lubricant (drum shaft, drum, steel wire rope and other useful parts) at each lubrication point according to the demand.

4.自动上料混凝土搅拌车齿轮减速机齿轮和轴承运用齿轮旋转将油送至油箱内壁并流向轴承进行润滑。有必要在燃油表的两条线之间坚持变速箱油位。假设油位过高或过低，每个部件的温度将升高或润滑缺乏，这将添加动力丢失并减少机器操作。

4. The gears and bearings of the gear reducer of the automatic feeding concrete mixer truck use gear rotation to send oil to the inner wall of the oil tank and flow to the bearings for lubrication. It is necessary to maintain the transmission oil level between the two lines of the fuel gauge. Assuming that the oil level is too high or too low, the temperature of each component will rise or there will be a lack of lubrication, which will add to the loss of power and reduce machine operation.

5.自动加料搅拌机选用的润滑油不含特定粘度和粘度温度特性，低凝固点，杰出的氧化稳定性，机械杂质和水分，耐腐蚀和耐磨材料。其质量指标有必要符合国家标准。

5. The lubricating oil selected for the automatic feeding mixer does not contain specific viscosity and viscosity temperature characteristics, low freezing point, excellent oxidation stability, mechanical impurities and moisture, corrosion-resistant and wear-resistant materials. Its quality index must conform to national standards.

自动上料混凝土搅拌车用于润滑，减少磨损并延长部件寿命。但是，添加润滑剂时要记住一些事项。应在初的150和300小时内替换新机器，以铲除在检验过程中未完全清洁的污垢。工作时，查看油位并及时添加。

The automatic loading concrete mixer is used for lubrication, reducing wear and prolonging the service life of components. However, there are some things to remember when adding lubricant. The new machine shall be replaced within the first 150 and 300 hours to remove dirt that has not been completely cleaned during the inspection. When working, check the oil level and add it in time.

挑选自动上料混凝土搅拌车的留心事项

Precautions for selecting automatic loading concrete mixer

1.油箱容量挑选：由于小方搅拌车相对较热，自动上料混凝土搅拌车在购买时需求留心小巧便当的外观。当然，您需求依据需求购买。

1. Selection of fuel tank capacity: as the small square mixer is relatively hot, the automatic feeding concrete mixer needs to pay attention to its compact and convenient appearance when purchasing. Of course, you need to buy according to your needs.

2.判别自动上料混凝土搅拌车罐体的质量：罐体的质量主要是指罐体的厚度。目前一般5mm厚的锰板，业主能够向厂家询问罐体厚度，假设厚度小于5mm，则不需求考虑。

2. Judge the quality of the tank of the automatic feeding concrete mixer: the quality of the tank mainly refers to the thickness of the tank. At present, the owner can ask the manufacturer about the thickness of the tank for the manganese plate with a thickness of 5mm. If the thickness is less than 5mm, it does not need to be considered.

3.依据运行杰出的路程状况：购买自动上料混凝土搅拌车时，需求依据运用情况设置基座。假设跑道十分平整，通常是路程。

3. According to the excellent running distance: when purchasing the automatic feeding concrete mixer, the base shall be set according to the application. Assuming that the runway is very flat, it is usually a long distance.

山东自动上料混凝土搅拌灌车的添加润滑油的留心问题和挑选了解就是这样了，期望对你有帮助。

Attention and selection of lubricating oil for Shandong automatic feeding concrete mixer truck is just like this. I hope it will be helpful to you.