The automatic feeding mixer is composed of two parts: main parts and working device. The main components are required by all automatic feeding mixer trucks. The working device is unique for different purposes.

一、主要部件包括发动机，变矩器，变速箱，前、后驱动桥，简称四大件：

1、 The main components include engine, torque converter, gearbox, front and rear drive axles, which are referred to as four major parts for short:

1、发动机。

1. Engine.

2、变矩器上有三个泵，工作泵（供应举升，翻斗压力油）转向泵（供应转向压力油）变速泵也称行走泵（供应变矩器，变速箱压力油），有些机型转向泵上还装有先导泵（供应操纵阀先导压力油）。

2. There are three pumps on the torque converter, working pump (supply lifting and tipping pressure oil), steering pump (supply steering pressure oil) variable speed pump, also known as travel pump (supply torque converter and transmission pressure oil). Some models of steering pump are also equipped with pilot pump (supply control valve pilot pressure oil).

3、工作液压油路，液压油箱，工作泵，多路阀，举升油缸和翻斗油缸。

3. Working hydraulic oil circuit, hydraulic oil tank, working pump, multi-way valve, lifting cylinder and tipping cylinder.

4、行走油路：变速箱油底壳油，行走泵，一路进变矩器一路进档位阀，变速箱离合器。

4. Traveling oil circuit: transmission oil pan oil, traveling pump, one way to the torque converter, one way to the gear valve, and transmission clutch.

5、驱动：传动轴，主差速器，轮边减速器。

5. Drive: transmission shaft, main differential, wheel reducer.

6、转向油路：油箱，转向泵，稳流阀（或者优先阀）转向器，转向油缸。

6. Steering oil circuit: oil tank, steering pump, steady flow valve (or priority valve), steering gear and steering cylinder.

7、变速箱有一体的（行星式）和分体的（定轴式）两种。

7. There are two kinds of transmission: integrated (planetary type) and split (fixed shaft type).

二、工作装置：

2、 Working device:

自动上料搅拌机的上料和装卸物料作业是通过其工作装置的运动来实现的。

The feeding and loading and unloading operations of the automatic feeding mixer are realized through the movement of its working device.

在我们的生活中，混凝土搅拌车是用于运输混凝土的特殊车辆，通常在该车辆后方装有一个大罐来搅拌混凝土。但是，由于需要长期清洁车辆内部的混凝土，因此下面介绍具体的清洁方法。

In our life, concrete mixer is a special vehicle used to transport concrete. Usually, a large tank is installed at the rear of the vehicle to mix concrete. However, since the concrete inside the vehicle needs to be cleaned for a long time, the specific cleaning methods are described below.

1.准备应急驱动软管，关闭搅拌车，并卸下液压马达的高压油管接头。

1. Prepare the emergency drive hose, close the mixer truck, and remove the high-pressure oil pipe connector of the hydraulic motor.

2.拆下高压油管，并用紧急驱动软管将其连接到故障汽车的相应接头。

2. Remove the high-pressure oil pipe and connect it to the corresponding connector of the faulty vehicle with the emergency drive hose.

3.对于发动机搅拌车，将控制手柄转到卸料位置，以去除搅拌车内的混凝土。

3. For the engine mixer, turn the control handle to the unloading position to remove the concrete in the mixer.

4.应急驱动器完成后，卸下驱动器软管，将车辆恢复到原始状态。

4. After the emergency drive is completed, remove the drive hose and restore the vehicle to its original state.

由于您中有些人可能已经知道如何清洁混凝土搅拌车内的混凝土，因此了解这些知识更好，以防止在使用过程中出现故障对设备正常运行的影响，我希望您能够做到这一点。

Since some of you may already know how to clean the concrete in the concrete mixer truck, it is better to understand this knowledge to prevent the impact of failure on the normal operation of the equipment during use. I hope you can do this.

以上就是为大家介绍的有关全自动自上料搅拌车的详细介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.jufengjiaobanji.com/

The above is a detailed introduction to the automatic self feeding mixer truck. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.jufengjiaobanji.com/